The upper and lower parts of the CAC4-A-63B-50 pressure reducing valve are leaking, which is due to the seal ring at the seal between the actuator and the cylinder not achieving a seal effect due to the frequent activity of the actuator. The material of the pressure relief valve should be able to meet the requirements of the medium's temperature, pressure, pressure difference, and corrosion resistance. In what aspects are the differences in the joints reflected? Below, let me explain for everyone: 1. The joint is mainly used to reduce the pressure of a branch oil circuit in the hydraulic system, making the branch pressure lower and stable than the main oil circuit pressure. Within the set pressure range, the pressure reducing valve is closed like a relief valve. However, as the system pressure increases and reaches the set pressure of the pressure reducing valve, the pressure reducing valve opens, and some of the oil will return to the oil tank through it (at this point, there is some pressure oil returning to the oil tank, and the oil temperature in the oil tank will rise), the oil pressure of this branch will not rise. It plays a role in reducing the pressure and stabilizing the pressure of this branch! The relief valve is different, it is installed at the outlet of the pump and will ensure the overall pressure stability of the system and will not overpressure. Therefore, it has safety, pressure regulation, and pressure stabilization functions! The wear condition of the sealing surface. Internal pilot soft slide valve compressed air 0.70 refer to the specifications of the following sub-machines 1.05-5~50 (but not frozen) 5~50 do not need dustproof 50 below/300 below should not be used in corrosive gas environments Valve type and operating method Maximum operating pressure MPa of the working fluid Minimum operating pressure MPa of the working fluid Guaranteed pressure resistance MPa Ambient temperature 0 C Fluid temperature 0 C Oil supply protection level Vibration/impact m/s 2 Operating occasions Item Content Note 1: The thread of the piping air port also corresponds to G thread, NPT thread, so please consult and negotiate. Note 2: The response time is the value when ON at a supply pressure of 0.5MPa, without lubrication. It will vary according to the change in pressure and the quality of the lubricating oil when supplied. Points to consider when selecting the model Note 1: For use under vacuum conditions with external pilot (K), please consult and negotiate. Note 2: The additional surge absorber in the DC24V situation, if the medium property is not within the applicable range of the solenoid valve, it may also cause the valve core to not operate. When using a rodless cylinder, everyone should carefully read the instruction manual to prevent the use of media that is not within the applicable range of the solenoid valve. Introduction to the advantages of servo motor installation; Direct control type proportional oil mist filter Plastic material oil cup guard Metal guard, flow direction from left to right from right to left Direct acting proportional oil mist filter Plastic cup + metal cup guard. Pressure reducing valve LR/LRS, D series, metal structure Peripheral components list, Micro single unit, with connecting plate, interface specifications Gx, QS4 or QS6, single unit, without connecting plate, used for air source treatment device combination Interface specifications Body M5 or M7, installation accessories, rotating handle, with lock Rotating handle 3. In places that do not affect operation, apply special paint (i.e., paint) to it, which is both beautiful and prevents rust. Discharged from the muffler, but in this case, the cylinder often cannot work properly. Introduction to the structure principle and characteristics of the cylinder Ensure that the radial and axial loads applied to the servo motor shaft during installation and operation are controlled within the specifications of each model.
Locking cylinder CAC4-A-63B-50 belongs to the Air Pressure Cylinders series under CKD company, model number CAC4-A-63B-50. To purchase or inquire about Locking cylinder CAC4-A-63B-50, you can directly contact 158 0047 0089 (Mr. He).
1. Cylinders: Used to convert the energy of compressed air into mechanical energy to produce linear motion.
2. Pneumatic valves: Used to control the direction, speed, and pressure of airflow, regulating the operation of pneumatic systems.
3. Pneumatic motors: Devices that convert compressed air into rotary motion.
4. Air tubes and connectors: Used to connect various components in pneumatic systems and transmit air.
Yes, CKD pneumatic components require regular maintenance to ensure normal operation and extend service life. Key maintenance points include:
- Regularly check and replace seals and gaskets to prevent air leakage.
- Inspect and clean filters to ensure clean air quality.
- Lubricate moving parts to reduce wear and improve efficiency.
- Check air tubes and connectors to ensure secure and undamaged connections.
When selecting the appropriate CKD pneumatic components, consider the following factors:
Application requirements: Understand the specific working environment and tasks, such as load, speed, and stroke.
Air source conditions: Ensure that the pressure and flow of the air source meet the component’s requirements.
Installation space: Confirm available space and choose components of suitable size.
Environmental factors: Consider the temperature, humidity, and potential corrosiveness of the working environment to select suitable materials and designs.
Common pneumatic system faults include:
Air leakage: Causes efficiency decline; check seals, connections, and tubes, find leak points, and repair or replace.
Stuck cylinder piston: Possibly caused by dirt or insufficient lubrication; clean the piston and add lubricant.
Valve failure: Check electrical control signals, ensure smooth airflow, and verify if the valve itself is damaged.
Insufficient pressure: Inspect air source pressure, filters, and piping to ensure no blockage or leakage.
