festoGuide cylinderDFM-80-50-P-A-KFOperating instructions for debugging work due to the design personnel for debugging, set the filter timing and clean conversion timing, the water to be treated enters the body from the inlet, the manual regulating valve starts normal work, when the preset cleaning timing is reached, the electronic controller sends signals to the hydraulic control valve and the drive motor, triggering the following actions: the electric motor drives the wheel to rotate, continuously cleaning the filter element, in addition, the control valve opens to continuously discharge pollutants, the entire cleaning process only takes a few tens of seconds, when the cleaning is finished, close the control valve, the motor stops turning, the system returns to its initial state, and starts the next filtering process. German solenoid valve What is the leakage of this valve specified as? From an economic perspective, users hope that a valve can be used for both throttling and regulation, and now it is possible. However, for regulating valves, the main purpose is to control the flow rate, and closing is secondary. It is wrong to think that small flow valves themselves have a very small flow rate, and it is easy to achieve throttling when closed. Foreign countries have also made regulations for the leakage of small flow regulating valves. When the Cv value is 10, the leakage of this valve is specified as German solenoid valve When disassembling and replacing valves, both sides of the fluid should be thoroughly cut off, the residual fluid should be discharged, and personnel protection should be done (wearing protective clothing, masks, gloves, etc.) to prevent corrosive fluids from harming people. The seal of the parts where the pneumatic gripper rotates or reciprocates is called dynamic sealing, and the seal of the stationary parts is called static sealing. 7, adjustable. Parameters such as filtration accuracy, sediment capacity, and filtration resistance can be adjusted according to needs; 2, lightweight. The clamp contact weight is light, the number of bolts is small, the installation is convenient, no special skills are required.festoGuide cylinderDFM-80-50-P-A-KFPneumatic laboratory molded packing rings ensure that the size of the ring matches the shaft or pneumatic laboratory precisely, if necessary, cut the packing rings according to the operating instructions or requirements of the packing ring manufacturer. The main technical parameters of the swing cylinder, valve function 3/2 5/2 5/3, normal position G1) O2) – – G1) B2) E3), memory steady state single double single, pneumatic reset is – no, mechanical reset no – yes, structural features piston slide valve, sealing principle soft sealing, driving method electric drive, control method pilot control, pilot air source internal pilot or external pilot, air flow direction external pilot bidirectional, exhaust function flow control, manual tool non-locked, locked with accessories, installation method through through hole, installation position arbitrary, air interface 1, 2, 4 thread interface M5, M7; QS interface 4 or 6 mm3, 5 thread interface M7, 12, 14 thread interface M3; QS interface 3, 82, 84 thread interface M3, nominal diameter [mm] 4, standard rated flow M5 [l/min] 190 180, standard rated flow M7 [l/min] 400 350 300 250, standard rated flow QS4 [l/min] 190 180, standard rated flow
Guided Cylinder DFM-80-50-P-A-KF belongs to the Air Pressure Cylinders series under CKD company, model number DFM-80-50-P-A-KF. To purchase or inquire about Guided Cylinder DFM-80-50-P-A-KF, you can directly contact 158 0047 0089 (Mr. He).
1. Cylinders: Used to convert the energy of compressed air into mechanical energy to produce linear motion.
2. Pneumatic valves: Used to control the direction, speed, and pressure of airflow, regulating the operation of pneumatic systems.
3. Pneumatic motors: Devices that convert compressed air into rotary motion.
4. Air tubes and connectors: Used to connect various components in pneumatic systems and transmit air.
Yes, CKD pneumatic components require regular maintenance to ensure normal operation and extend service life. Key maintenance points include:
- Regularly check and replace seals and gaskets to prevent air leakage.
- Inspect and clean filters to ensure clean air quality.
- Lubricate moving parts to reduce wear and improve efficiency.
- Check air tubes and connectors to ensure secure and undamaged connections.
When selecting the appropriate CKD pneumatic components, consider the following factors:
Application requirements: Understand the specific working environment and tasks, such as load, speed, and stroke.
Air source conditions: Ensure that the pressure and flow of the air source meet the component’s requirements.
Installation space: Confirm available space and choose components of suitable size.
Environmental factors: Consider the temperature, humidity, and potential corrosiveness of the working environment to select suitable materials and designs.
Common pneumatic system faults include:
Air leakage: Causes efficiency decline; check seals, connections, and tubes, find leak points, and repair or replace.
Stuck cylinder piston: Possibly caused by dirt or insufficient lubrication; clean the piston and add lubricant.
Valve failure: Check electrical control signals, ensure smooth airflow, and verify if the valve itself is damaged.
Insufficient pressure: Inspect air source pressure, filters, and piping to ensure no blockage or leakage.
